Here is my latest 7159kc xtal based CW transmitter.
And 4diode product detector or ta7358ap DC RECEIVER IN MAKING.
I made chassis years ago and it was sitting around. Made the 2watt linear.The xtal 7.159mhz cw oscillator small single transistor tx board was also made earlier. see relevant post back in time.
I was wondering if, i can put a xtal transmitter on air and come up on-air with cw. I had plenty of 40 meter 7159kc DC as well as 3579kc xtal based poliakov receivers. Interesting. I can put my another local ham into air with me to practice my slow cw skill.
logically i started building it. humm ..... with a big linear it produced around 15 watts. it can surely punch a hole through India. i can put dipole, random longwire as well as EFHW vertical also.
Date 14-12-2018:---Then i started building the suitable box for linear as my previous experience with unboxed linear was that i broke two IRF640 mechanically. It did not breakdown due to heat or vswr !
i was making a box with a big fan, where i can put the linear board as we do in cabinet. But, that building experiment failed due to mechanical problems. Then i said lets do logical work. linear is working. we will put into box later on.
Meanwhile i started searching the net and fake buck groups to find a c language code for Arduino to key my call in cw. CQ CQ CQ DE VU3INJ VU3INJ VU3INJ K and in this quest, good hams helped me and lead me to various arduino based keyers. Wow. i said this is good keyers but my Task can be done even with the multivibrator driving relay which keys my tx on off. So finally, i settled for a simple sketch which keys my tx. will upload that to my uno board and then explore digitally. but that will take time.
Date 18-12-2018:---Antenna is not ready, receiver is not ready. earlier i had bad results using the good receiver in vicinity of transmitter. So i will be using portable homebrew receiver and FSM to measure its LOCAL range. Second thing i want basically a point to point communication around 100km. two places are of my interest. one is my another home and my kids hostel.
Date 19-12-2018:--- I am trying out the QSK for receiver. i do not want any relay chatterings. Its clattering is not good for this small receiver. I will be using a diode based QSK which is well tested by my dear old friend VU2ATNs in his 20 meter CW QRP transmitter. Fact is that, for the first time i etched the pcb and made a cw transmitter for a college project. OM Atanu is good ham and he published many ckt in Electronics For You Magazine. But in bitx bandwagon his projects did not get much publicity.
The receiver is a very modular approach. I made various modules over the time.I had a box full boards from these i found two working modules. I am using jumpers etc so when i do want to replace any AF, PD board etc its just remove the wire and its done. Will try ring-diode based receiver as well as TA7358ap based receiver. I am steadily working. My office-room looks like a scrap room. My client wondered that are you started dealing in radio repair ? Nope. Anyway.
I was in deep pain . It was physical one. There is some stomach problem and it itches. Then i heard that my beloved ELMER vu2dev is SK. In-fact i wanted to have QSO with him on my new TX RX. But alas that could nit happen.Anyway its better to finish it now.
On date 25 dec the xmus is coming here and i want to make QRM still rx is lagging by. Solved the diode series switch issue. It reduces the antenna input going to ta7358 drastically but still it leaks. So i need a controlled gain rf amp and diode switch . filter tanks. Ohh Jesus, lots of work. :)
The dummy loads problem solved, RF indicator LED not lighting ? So i removed the 0.1 mfd cap and presto the LED lights up on RF. Good.
Fitted the receiver in place. Tested both the boards. I had made them on 2015 imagine 3 years they were sitting idle. Now show time. Solved dry connection. Put connectors. Okey and somehow my new soldering iron gone qrt. Tested rx without any front end. Ok. It can withstand rf. Time to put up qsk and then change xtal to 7024KC with RIT.
Now lets solve the QSK . I will use the switch as suggested by m0dgq.
Its
simple when diode is given firward dc bias it conducts and has low
resistance. When reverse biased it has high resistance and blocks the
passing of RF. Higher the frequencies less the separation. Bulkier the
diode less usable in rf. We use back to back diode to get greater
separation. Thats it folks. Now time to make rf switching filter tuned
ckt FRONT END CARD. As antenna will be big there will be BCB. And QRM .
So filter and amp needed.
Wait folks. I have requested a very seniour ham to give me some 7059 xtals. but i doubt it will ever arrive.
;-date 31 dec 2018. Finally boxed up whole set up and trying to do some qrm-party. I noticed few problems.
1- Loose connections due to homemade connectors.
2- RF is being leaked from keying amp to succedding stages. So xtal osc needs to be keyed.
3- It seems antenna is not connected to RF fron end
4- I need to use relay to derive Tx-Rx voltage and Antenna Tx-Rx handover. Despite all these qsk diodes i need the relay.
5- For practical use the VXO is needed. Time to change vxo and rf amp. Otherwize its good as standalone beep beep beep.
The 2Watt linear is OK when used with my 2 amp 12v DC supply the Vcc voltage line do not drop and i can get good power. at 12vdc 650ma current. and at key down 20 ma. Good enough for tx chain. At present loading the antenna - a random wire of about 50 feets just 10 feet high. It does not show up in crude FSM made of diodes but its sounds OK in the DEV 40 meter analogue receiver without any antenna.
I will once again make the QSK ckts and see that whether the receiver gets the antenna. Thats it folks. So listen to my canary bird singing beeps on 7159kc. Thats it folks. End of this phase. The Tx-Rx are working. The wheel has been re-invented and re-used or abused. Its working. ENJOY.
And 4diode product detector or ta7358ap DC RECEIVER IN MAKING.
I was wondering if, i can put a xtal transmitter on air and come up on-air with cw. I had plenty of 40 meter 7159kc DC as well as 3579kc xtal based poliakov receivers. Interesting. I can put my another local ham into air with me to practice my slow cw skill.
logically i started building it. humm ..... with a big linear it produced around 15 watts. it can surely punch a hole through India. i can put dipole, random longwire as well as EFHW vertical also.
Date 14-12-2018:---Then i started building the suitable box for linear as my previous experience with unboxed linear was that i broke two IRF640 mechanically. It did not breakdown due to heat or vswr !
i was making a box with a big fan, where i can put the linear board as we do in cabinet. But, that building experiment failed due to mechanical problems. Then i said lets do logical work. linear is working. we will put into box later on.
Meanwhile i started searching the net and fake buck groups to find a c language code for Arduino to key my call in cw. CQ CQ CQ DE VU3INJ VU3INJ VU3INJ K and in this quest, good hams helped me and lead me to various arduino based keyers. Wow. i said this is good keyers but my Task can be done even with the multivibrator driving relay which keys my tx on off. So finally, i settled for a simple sketch which keys my tx. will upload that to my uno board and then explore digitally. but that will take time.
Date 18-12-2018:---Antenna is not ready, receiver is not ready. earlier i had bad results using the good receiver in vicinity of transmitter. So i will be using portable homebrew receiver and FSM to measure its LOCAL range. Second thing i want basically a point to point communication around 100km. two places are of my interest. one is my another home and my kids hostel.
Date 19-12-2018:--- I am trying out the QSK for receiver. i do not want any relay chatterings. Its clattering is not good for this small receiver. I will be using a diode based QSK which is well tested by my dear old friend VU2ATNs in his 20 meter CW QRP transmitter. Fact is that, for the first time i etched the pcb and made a cw transmitter for a college project. OM Atanu is good ham and he published many ckt in Electronics For You Magazine. But in bitx bandwagon his projects did not get much publicity.
 |
| QSK |
The receiver is a very modular approach. I made various modules over the time.I had a box full boards from these i found two working modules. I am using jumpers etc so when i do want to replace any AF, PD board etc its just remove the wire and its done. Will try ring-diode based receiver as well as TA7358ap based receiver. I am steadily working. My office-room looks like a scrap room. My client wondered that are you started dealing in radio repair ? Nope. Anyway.
I was in deep pain . It was physical one. There is some stomach problem and it itches. Then i heard that my beloved ELMER vu2dev is SK. In-fact i wanted to have QSO with him on my new TX RX. But alas that could nit happen.Anyway its better to finish it now.
On date 25 dec the xmus is coming here and i want to make QRM still rx is lagging by. Solved the diode series switch issue. It reduces the antenna input going to ta7358 drastically but still it leaks. So i need a controlled gain rf amp and diode switch . filter tanks. Ohh Jesus, lots of work. :)
The dummy loads problem solved, RF indicator LED not lighting ? So i removed the 0.1 mfd cap and presto the LED lights up on RF. Good.
Fitted the receiver in place. Tested both the boards. I had made them on 2015 imagine 3 years they were sitting idle. Now show time. Solved dry connection. Put connectors. Okey and somehow my new soldering iron gone qrt. Tested rx without any front end. Ok. It can withstand rf. Time to put up qsk and then change xtal to 7024KC with RIT.
Now lets solve the QSK . I will use the switch as suggested by m0dgq.
Wait folks. I have requested a very seniour ham to give me some 7059 xtals. but i doubt it will ever arrive.
;-date 31 dec 2018. Finally boxed up whole set up and trying to do some qrm-party. I noticed few problems.
1- Loose connections due to homemade connectors.
2- RF is being leaked from keying amp to succedding stages. So xtal osc needs to be keyed.
3- It seems antenna is not connected to RF fron end
4- I need to use relay to derive Tx-Rx voltage and Antenna Tx-Rx handover. Despite all these qsk diodes i need the relay.
5- For practical use the VXO is needed. Time to change vxo and rf amp. Otherwize its good as standalone beep beep beep.
The 2Watt linear is OK when used with my 2 amp 12v DC supply the Vcc voltage line do not drop and i can get good power. at 12vdc 650ma current. and at key down 20 ma. Good enough for tx chain. At present loading the antenna - a random wire of about 50 feets just 10 feet high. It does not show up in crude FSM made of diodes but its sounds OK in the DEV 40 meter analogue receiver without any antenna.
I will once again make the QSK ckts and see that whether the receiver gets the antenna. Thats it folks. So listen to my canary bird singing beeps on 7159kc. Thats it folks. End of this phase. The Tx-Rx are working. The wheel has been re-invented and re-used or abused. Its working. ENJOY.
